[ace-users] How do I build with Borland Developer Studio 2006?

Johnny Willemsen jwillemsen at remedy.nl
Sat Jul 7 11:13:20 CDT 2007


Hi,

You should use the borland make, make --version or make --? To check that
you have the borland make

Regards,

Johnny Willemsen
Remedy IT
Postbus 101
2650 AC  Berkel en Rodenrijs
The Netherlands
www.theaceorb.nl / www.remedy.nl  

*** Integrated compile and test statistics see
http://scoreboard.theaceorb.nl ***
*** Commercial service and support for ACE/TAO/CIAO             ***
*** See http://www.theaceorb.nl/en/support.html                 ***

<tieman at aps.anl.gov> wrote in message
news:<1183751340.831006.185890 at e9g2000prf.googlegroups.com>...
> Hmmm...the steps listed in TPG are exactly those I did.  I tried them
> all again with the same results.
> 
> I don't understand what "Error ACE.bor 17: Command syntax error"
> means.  Should I be using a different make (GNU for instance?) than
> the one that comes with BCB?  I'm guessing the error is coming from
> make which would imply it can't understand the makefile...but the
> makefile is unmodified from the ACE distribution (5.5) so I don't
> understand what's wrong.
> 
> Thanks again!
> 
> Brian
> 
> On Jul 6, 2:22 pm, "Johnny Willemsen" <jwillem... at remedy.nl> wrote:
> > Hi,
> >
> > Seewww.theaceorb.nlfor the TAO Programmers Guide, this contains a
section
> > how to build with C++ Builder.
> >
> > Regards,
> >
> > Johnny Willemsen
> > Remedy IT
> > Postbus 101
> > 2650 AC  Berkel en Rodenrijs
> > The Netherlandswww.theaceorb.nl/www.remedy.nl
> >
> > *** Integrated compile and test statistics
seehttp://scoreboard.theaceorb.nl***
> > *** Commercial service and support for ACE/TAO/CIAO             ***
> > *** Seehttp://www.theaceorb.nl/en/support.html                ***
> >
> > <tie... at aps.anl.gov> wrote in message
> >
> > <news:1183746694.270008.230560 at 57g2000hsv.googlegroups.com>...
> >
> > > Hi all!
> >
> > > I've built ACE just fine under Linux...now I need to build it under
> > > Windows and link it to a CBuilder 2006 program.
> >
> > > I've done the following:
> >
> > > 1) Created file ACE_ROOT\ace\config.h with the following line:
> > > #include "ace/config-win32.h"
> > > 2) set ACE_ROOT=C:\ACE_wrappers
> > > 3) set BCBVER=8
> > > 4) cd ACE_ROOT\ace
> > > 5) make -f Makefile.bor all
> >
> > > and I get
> >
> > > MAKE Version 5.2  Copyright (c) 1987, 2000 Borland
> > >    make -l -o          -f ACE.bor all
> > > MAKE Version 5.2  Copyright (c) 1987, 2000 Borland
> > > Error ACE.bor 17: Command syntax error
> > > Error ACE.bor 19: Command syntax error
> > > Error ACE.bor 21: Command syntax error
> > > Error ACE.bor 23: Command syntax error
> > > Error ACE.bor 25: Command syntax error
> > > Error ACE.bor 27: Command syntax error
> > > Error ACE.bor 29: Command syntax error
> > > Error ACE.bor 31: Command syntax error
> > > ...
> >
> > > as output.  I followed the instructions listed at:
> >
> > http://www.dre.vanderbilt.edu/~schmidt/DOC_ROOT/ACE/ACE-INSTALL.html#...
> >
> > > but I'm not sure what's wrong.  Anyone have an idea about how to move
> > > forward from here?
> >
> > > Thanks!
> >
> > > Brian
> 
> 



More information about the Ace-users mailing list